No hot water at all
The breaker has tripped, the high-limit safety switch has tripped, or both heating elements have failed. A bad thermostat can do the same thing.
Electric tank water heaters
Cold showers, lukewarm water, or a breaker that keeps tripping? Electric heaters usually fail in a few predictable ways, and the parts involved run on high-voltage power. Here is what is likely going on, what you can safely look at, and when to call.
Speak with a water heater specialist.

An electric water heater runs on its own high-voltage circuit, and its heating elements sit inside a tank full of water. Do not take panels off or touch wiring on a heater that has power. If there is water on or near the electrical parts, a burning smell, or a breaker that will not stay on, switch the heater’s breaker off and call.
Start with what you notice
This is what usually sits behind each symptom. It is a guide to the likely cause, not a repair plan.
The breaker has tripped, the high-limit safety switch has tripped, or both heating elements have failed. A bad thermostat can do the same thing.
Often one of the two elements has stopped working, usually the lower one. Sediment on the elements makes it worse.
A shorted element, loose or damaged wiring, or a failing thermostat. Resetting it again and again is not a fix. See water heater repair.
A stuck thermostat or a failed high-limit switch. Hot enough to scald is a safety problem, so turn the heater off at the breaker and call.
Water trapped under a layer of sediment on the bottom of the tank, boiling and bubbling up through it.
It could be a fitting or the relief valve, or the tank itself. Water near electric parts is a reason to cut the power first. See emergency water heater repair.
What wears out

Safe to check, and what is not
An electric heater normally has its own double breaker, often labeled for the water heater. If it is tripped, flipping it fully off and then on once is reasonable. If it trips again, stop and call. Something is wrong, and more resets will not fix it. For a breaker that keeps tripping, see water heater repair.

Leaks and safety valve
The temperature and pressure relief valve is a safety part on every tank heater, with a pipe that carries any release down toward the floor. A steady drip or spray from it is a sign something is wrong, with the pressure, the temperature or the valve itself. Do not cap or plug that pipe.
Water at the base can be a loose fitting or the valve. If it is coming from the tank body, the tank has failed. A drain pan under the heater, like the one below, catches a slow leak, but it will not fix one.


When you call
You tell us what the heater is doing: no heat, not enough, a breaker that trips, water where it should not be. We ask whether it is electric, how old it is if you know, and what you have already looked at. From that we can say what is likely wrong and what to do next. We do not quote times or prices on this page, so ask about both on the call.
Repair or replace
An element, a thermostat or a high-limit switch can usually be replaced. Water around the tank? See water heater leaking. A tank that has corroded through cannot be repaired. If a heater is old and keeps needing work, replacement may make more sense. See water heater repair for repairs in general or replacement and installation if the tank is done. Heater still working? See water heater maintenance and flushing. Have a gas heater instead? See gas water heater repair. Have an electric tankless unit? See tankless water heater repair. Thinking about a heat pump (hybrid) electric unit? See heat pump water heater installation. Thinking about going tankless? See tankless installation. Cold taps and not sure why? No hot water: what to check first covers gas and electric.
Service area
A plumber. Even though it runs on electricity, the heater is tied into pressurized water lines and a relief valve. Call us and describe what it is doing.
Common causes are a tripped breaker, a tripped high-limit switch, a failed heating element or a bad thermostat. Checking the breaker is safe. Anything behind the access covers is not.
Usually one of the two heating elements has failed, so only part of the tank is being heated. Sediment in the tank can do it as well.
Yes, many have a red high-limit reset button behind the upper access cover. It sits near live wiring, so leave it to a plumber. If it has tripped, the cause still needs to be found.
A shorted element, damaged wiring or a failing thermostat. Do not keep resetting it. Switch it off and call.
Looking at the breaker and for water around the base is fine. Opening the covers, testing parts or touching wiring is not, because of the power and the water. Leave that to a licensed plumber.
Check the breaker, keep the covers on, then call and tell us what it is doing. Waxahachie, TX and nearby towns.
Tap to call(972) 472-8849