No hot water at all
No power, a closed or blocked supply, an ignition or flame fault on a gas unit, a safety shutoff, or a failed part.
Gas and electric tankless units
No hot water, a code on the display, or water that swings between hot and cold? Tankless heaters fail in different ways than tank heaters, and gas and electric units fail in different ways from each other. Call and tell us what yours is doing.
Speak with a water heater specialist.

Safety first
Gas or electric?
It matters, because the parts that can go wrong are not the same. If you are not sure, look for a gas line and a vent pipe. Tell us what you see when you call.
Has a gas line with a shut-off valve, a sealed vent pipe or pipes, and usually a plug for the controls. Gas units have to light a burner, so problems often involve ignition, venting, gas supply or the heat exchanger.
Has no gas line and no vent pipe. It runs on a heavy electrical supply, often with a disconnect or its own breaker. Problems are more likely to involve power, heating elements, sensors or flow.

What is going wrong?
These are general possibilities, not a diagnosis. Only a look at your unit tells you which one it is.
No power, a closed or blocked supply, an ignition or flame fault on a gas unit, a safety shutoff, or a failed part.
Scale inside the unit, a clogged inlet filter, low flow through the heater, or a sensor that is reading wrong.
A short gap in hot water when you shut a tap off and back on. Often tied to how the unit senses flow, and sometimes to the plumbing around it.
The unit has found a fault, such as ignition, venting, overheating or low flow. The code narrows it down. See the next section for what to do with it.
A clogged filter, scale, or a problem on the supply side. If cold water is weak too, it may not be the heater at all.
Scale, a blocked vent, or a part that is struggling. A unit that keeps shutting itself off needs a look.
Loose or worn water connections, a condensate drain problem on a high efficiency gas unit, or a leak inside the heater. Active leaks need a plumber.
Error codes
The easiest useful thing you can do is read what the screen says. Write down the exact code or the blinking pattern, and note whether the unit is gas or electric. That helps us work out what to bring and what to ask.
Codes mean different things on different models, so we do not list them here. Do not reset the unit again and again to get it running. If it keeps coming back, call.

What is safe to check

What gets checked

When you call
You tell us what the unit is doing and what the display says. We ask whether it is gas or electric, how old it is if you know, and whether anything has changed. From that we can tell you what is likely going on and what the next step is. We do not guess prices or arrival times here, so ask about timing on the call.
Repair or replace
Many tankless problems come from scale, a filter, a sensor or a vent, and those can be repaired. A heat exchanger that has failed, or a unit with repeated faults, is a different conversation. See replacement and installation or tankless water heater installation if you are thinking of a new unit.
Service area
Often, yes. Scale, a clogged filter, a sensor, an ignition part or a vent problem can usually be fixed. A failed heat exchanger or repeated faults may point to replacement.
Mineral buildup is a common one, especially with hard water. Vent and ignition problems on gas units, and flow or sensor problems, come up too.
It could be power, gas supply, a blocked vent, scale, low flow or a failed part. Write down any code on the display and call, and we will help sort out which.
A plumber who works on tankless units. They involve gas, electrical and water connections together. Call us and describe what is happening.
Looking at the display and the outside vent opening is fine. Opening the cabinet, working on gas, vent or electrical parts is not, and can be dangerous.
Tell us what it is doing and what the display says. Waxahachie, TX and nearby towns.
Tap to call(972) 472-8849